Set Up the Bitaxe Touch Turbo in Australia
Unbox the Bitaxe Touch Turbo, power it from the included AU-plug supply, join 2.4 GHz Wi-Fi, set your address and pool, set the clock, and keep it updated.
The Bitaxe Touch Turbo is a desktop solo miner with a 4.3-inch touchscreen. It runs on a 12.4 V supply from the box and, as listed, does 2.15 TH/s at about 43 W. This guide takes you from the box to a miner submitting shares, and points you to our existing pool guides for the last step.
Solo mining is a lottery ticket. Rewards are not guaranteed, and a miner this size is unlikely to find a block. It is a fun, hands-on way to take part in the network.
Safety first
- Use the supply in the box. The Touch Turbo takes 12 V DC through an XT30 connector. The Bitaxe models we have covered before take 5 V through a barrel plug. Never swap supplies.
- Mains power. Plug the supply directly into a wall socket. Do not use damaged cables or a power board with a loose fit.
- Keep it ventilated. The miner is a heat source. Do not cover it or push it into a cupboard.
- Do not hold the heatsink or fan while it runs. Hold the enclosure.
What you will need
- A Bitaxe Touch Turbo Solo Miner (AU Plug), from AU$549.
- A computer or phone on the same Wi-Fi network.
- Your router’s login (to check the Wi-Fi bands).
- A Bitcoin address you control. If you do not have one, set up a wallet with our hardware wallet guide first.
Step 1: Unbox
According to the shop listing, the box contains:
- The Bitaxe Touch Turbo solo miner in black
- A 12.4 V, 10 A XT30 power supply with an Australian plug
- A quick-start card
- A holographic sticker sheet
The listing describes a black 3D-printed enclosure with honeycomb ventilation and rubber feet, a 60 mm aluminium heatsink and a 60 mm fan. Check for cracks or loose parts and keep the quick-start card.
Step 2: Check your Wi-Fi bands
The Touch Turbo supports 2.4 GHz Wi-Fi only, so check this before you power on.
- Open your phone’s Wi-Fi list or your router’s Wi-Fi page.
- Look for a network on 2.4 GHz. Many NBN modems broadcast one name for both 2.4 GHz and 5 GHz, which can leave the miner unable to see a network it can use.
- If your modem has a setting to split the bands, or a separate 2.4 GHz network, turn it on and give it its own name, for example
MyWifi-2G. The setting name varies by modem, so check your modem’s manual or app. - Keep the password simple enough to type on a touchscreen.
Splitting the bands is general router advice, not a Bitaxe-specific step. The 2.4 GHz-only limit comes from the listing and the maker’s setup page.
Step 3: Power on
- Plug the XT30 connector from the supply into the miner. It only fits one way, so do not force it.
- Plug the supply into the wall and switch it on.
- Wait for the touchscreen to light up. The fan should spin.
If nothing happens, check the connector and the power point before you assume a fault.
Step 4: Join your Wi-Fi
The maker’s setup page sets Wi-Fi on the touchscreen:
- On the touchscreen, open the Wi-Fi screen.
- Tap Scan Networks.
- Choose your 2.4 GHz network from the Network Name (SSID) list.
- Enter the Password and tap Connect.
- Return to the home screen. The IP address is shown on the Wi-Fi settings screen. Write it down.
Set Wi-Fi on the touchscreen.
Step 5: Open AxeOS
- On a computer or phone on the same network, open a browser.
- Type the IP address from the touchscreen, as
http://and then the address. - The AxeOS dashboard loads. If it does not, check that the device and your computer are on the same network (and that your computer is not on a guest or 5 GHz-only network that blocks local devices), then reboot the miner and try again.
AxeOS also answers at http://bitaxe on networks that support mDNS, according to the official ESP-Miner readme.
Step 6: Enter your Bitcoin address
- In AxeOS, open the Pool tab.
- In User, enter a Bitcoin address that you control. A factory address may be pre-filled. Replace it.
- Do not save until you have chosen a pool in Step 7.
Do not type your seed words anywhere in AxeOS. It only needs a public receiving address. If you do not hold your own keys yet, set that up first with our hardware wallet guide.
Step 7: Choose a pool
Pool settings are the same as for other Bitaxe miners. Use one of our guides rather than repeating them here:
- Connect your Bitaxe to ausolo.ckpool.org
- Connect your Bitaxe to Parasite Pool
- Connect your Bitaxe to Public Pool
The maker’s page says to fill in Stratum Host, Stratum Port and User (your address) on the Pool tab, set Password to x, configure a fallback pool, then click Save and Restart. Follow the pool guide you choose for the exact values.
Step 8: Set the clock
The touchscreen has a digital clock with timezone selection.
- On the touchscreen, open Settings.
- Find the Time Zone drop-down under the clock settings.
- Choose Australia/Sydney if you live in New South Wales, Victoria, the ACT or anywhere else on the same time and daylight saving.
In the screen firmware’s current source code, Australia/Sydney is the only Australian entry. The other entries are UTC, US zones, Europe/London, Europe/Berlin and Asia/Tokyo. Sydney time follows daylight saving, so choosing it elsewhere gives the wrong time: Queensland has no daylight saving, and Perth, Adelaide and Darwin are on different offsets. The clock is a display feature and does not change mining. Firmware releases may add more zones.
Step 9: Learn the eight screens
The listing says the touchscreen has eight displays, in this order:
- Mining dashboard with hashrate, power, temperature and share statistics
- Bitcoin block clock
- Latest mined blocks
- Digital clock with timezone selection
- Live Bitcoin price
- Wi-Fi setup
- Performance, fan, brightness and update settings
- Live hashrate graph
The maker’s setup page lists the performance modes as Low, Medium and High, the fan option as an Automatic Fan Control checkbox, and brightness from 5% to 100%. Leave it on the default mode while you settle in.
Step 10: Placement and heat
The listing gives about 35 dB of noise and the 60 mm fan, with honeycomb ventilation on the enclosure.
- Put it on a hard, flat surface, such as a desk or shelf. Use the rubber feet. Do not put it on a bed, a couch or a towel.
- Leave open space around the vents. Keep it out of direct sun and away from other heat sources.
- Australian summers matter. A closed room or a sunny window will run hotter than a cool study.
- Keep Automatic Fan Control on unless you have a reason not to.
- The maker’s page says that if the device enters Overheat Mode, you should improve airflow, reduce the performance mode, or enable automatic fan control.
The listing says about 43 W at default settings, and nearly all of that ends up as heat in the room. Do not leave it in a confined space.
Step 11: Check it is working
- On the touchscreen, check the mining dashboard for hashrate, power and temperature.
- In AxeOS, check that shares are being accepted.
- Watch it for an hour. Hashrate varies, as it is a rolling figure.
The listing’s default is 2.15 TH/s. Your displayed figure will move around that.
Firmware updates
There are two firmwares, and they update separately.
AxeOS (mining firmware). The official source is the ESP-Miner releases page. As of 1 November 2026 the latest release is v2.15.4 (21 October 2026), and its assets include a build for board 801, the Bitaxe GT 801 platform named in the listing. Follow the update steps on the release and the readme.
- The ESP-Miner readme says current unified releases embed the web interface in
esp-miner.bin, and a separatewww.binis no longer required for standard use. The maker’s page (written for AxeOS v2.13.0) mentions uploadingwww.binas well. If the two disagree, follow the official repository for the release you are installing. - The maker’s page warns that the USB-C port on the left is for the miner, and that the bottom USB-C port is for the screen.
Screen firmware (BAP-GT-TOUCH). The official repository is bitaxeorg/BAP-GT-TOUCH. The latest release there is v1.1.2 (7 March 2026). Its release notes describe the over-the-air update: go to the Settings screen on the device, tap CHECK FOR UPDATES, and the device downloads and installs automatically. The maker’s page says Wi-Fi is required.
Before updating, make a note of your pool settings in case you need to re-enter them.
Troubleshooting
The screen is on but there is no Wi-Fi
Check you chose a 2.4 GHz network, the password is right, and the router is not blocking new devices. Split the bands if your modem combines them.
AxeOS will not load
Confirm your computer is on the same network as the miner, not a guest network. Reboot the miner and try the IP again. The maker’s page gives the same advice.
Hashrate is zero or it is not hashing
The maker’s page says to check the Stratum host, port and address, then Save and Restart. Also check the pool guide you followed.
Many rejected shares
The maker’s page suggests checking Stratum settings and trying a different pool or port.
It is running hot or in Overheat Mode
Improve airflow, reduce the performance mode, or enable automatic fan control, as the maker’s page suggests. Move it somewhere cooler.
The clock is wrong
Set the Time Zone again. If your city is not Sydney’s zone, see Step 8.
What’s next
The maker’s own documentation is on Solo Satoshi: How to set up the Bitaxe Turbo Touch.
This is general information, not financial, tax or legal advice. Electricity costs, hardware and rewards vary, and there are no guaranteed returns from solo mining.
Sources checked 1 November 2026: shop listing for the Bitaxe Touch Turbo Solo Miner (AU Plug); maker’s setup page (AxeOS v2.13.0, dated 2 March 2026); ESP-Miner readme and releases; BAP-GT-TOUCH releases and settings.c.
Frequently Asked Questions
What is in the box?
According to the shop listing: the Bitaxe Touch Turbo solo miner in black, a 12.4 V 10 A XT30 power supply with an Australian plug, a quick-start card and a holographic sticker sheet.
Can I use the 5 V supply from another Bitaxe?
No. The listing gives the power input as 12 V DC through an XT30 connector. Use the supply from the box. Do not swap power supplies between different Bitaxe models.
Does it work on 5 GHz Wi-Fi?
No. The listing and the maker's setup page both say 2.4 GHz only. If your NBN modem combines bands under one name, create or enable a separate 2.4 GHz network for the miner.
Which time zone should I choose?
In the touchscreen firmware's current source code, Australia/Sydney is the only Australian entry. It follows eastern daylight saving. If you are in Queensland, South Australia, Western Australia, the Northern Territory or Tasmania, the clock may be an hour or more out until the firmware adds your zone. This does not affect mining.
How many TH/s does it do?
The listing gives 2.15 TH/s by default, drawing about 43 W. Solo mining is probabilistic and rewards are not guaranteed.
What are the two firmwares?
The shop listing names open-source AxeOS mining firmware and BAP-GT-TOUCH screen firmware. AxeOS runs the mining. BAP-GT-TOUCH runs the touchscreen and is updated separately.