SeedSigner Plus Battery Edition: Fit, Boot and Use
Fit three AAA batteries, flash and verify the SeedSigner OS, and sign cable-free with the SeedSigner Plus Battery Edition. Safety, battery tips and troubleshooting.
The SeedSigner Plus Battery Edition is a SeedSigner signing device that runs from three AAA batteries instead of a cable. You carry it, insert the batteries, sign, then take the batteries out. This guide covers fitting the batteries, putting the official SeedSigner OS on the microSD card, a first boot, and what to do when it will not start.
What it is and who it suits
It does the same job as any other SeedSigner. The listing says all functions are exactly the same as the other SeedSigners. It suits you if you want to sign away from a power point, or you like a device with nothing to plug in. A SeedSigner signs by QR code, so it never needs a data connection to your computer or phone.
This guide is built from the shop listing, its four photos and the official SeedSigner project.
What is in the box
From the shop listing (AU$275):
- The SeedSigner Plus Battery Edition, in a 3D printed case. Body, buttons and faceplate come in a choice of colours.
- A 25 cm cable, your choice of USB A to USB C or USB C to USB C.
- Not included: the three AAA batteries.
The listing describes a 2.8 inch IPS 240x320 display, a DPAD, a spring-loaded microSD port, a power-only USB-C port, TPU buttons and a Raspberry Pi Zero v1.3 board.
A microSD card comes in the box, preloaded with SeedSigner OS so you can check the device boots straight away and for diagnostics. For real use, we recommend you download, verify and flash the OS onto a card yourself, so you know exactly what is running. Steps 2 to 4 show how.
Safety first
Read this before you fit anything or touch a seed.
Seed words are the money. Anyone who sees them can take your bitcoin. Never photograph them, type them into a phone or computer, or store them in the cloud.
- Seed hygiene. Create or load seeds in a private room. Phones off and out of the room. No webcams or smart speakers.
- Verify the OS yourself. Do not run a SeedSigner image you have not checked. See Step 3.
- Fit batteries the right way round. Reversed cells can damage the device and the batteries. Check each cell’s + and - against the markings before the cover goes on.
- Do not mix old and new batteries, or different brands or types. One weak cell drags down the set.
- Take the batteries out for storage. Cells left in a device can leak. Remove them whenever you are done, which the listing also asks you to do.
- Dispose of flat batteries properly. Do not bin them with general rubbish. Use a battery recycling point.
- Keep spare batteries and the open compartment away from small children.
Step 1: Know the device
The listing photos show:
- Front: a five-way DPAD on the left, three buttons on the right, and the screen in the middle.
- Back: a camera lens on one side and a rectangular battery cover on the other.
- Battery compartment: with the cover off, three AAA cells sit side by side, lengthwise, in a holder. In the photo, the top and bottom cells face one way and the middle cell faces the other, so the + ends alternate. The cover lifts away completely and has a small notch on one edge.
Fit the cells matching the + and - marks on your unit, and do not force a cell in.
Step 2: Get the official OS
The SeedSigner project’s 0.8.7 release is the latest at the time of writing (8 July 2026). The shop listing says this device has a Raspberry Pi Zero v1.3 board, and the release notes say the pi0 image is for the Pi Zero v1.3. Download:
seedsigner_os.0.8.7.pi0.imgseedsigner.0.8.7.sha256.txtseedsigner.0.8.7.sha256.txt.sig
Only download from the official project at github.com/SeedSigner, as the listing says.
Step 3: Verify the download
Do this before you open or write the image. The SeedSigner project’s README has the full instructions and screenshots. In short:
- Import the project’s public key and run GPG’s verify on the
.sigfile. You need a “Good signature”, and the key fingerprint must match the one the project publishes. Stop on “Bad signature”. - Check the image against the signed hash list. On Mac or Linux, use
shasum -a 256 --ignore-missing --checkon the.sha256.txtfile. On Windows, useCertUtil -hashfile <image> SHA256and compare the value to the list by eye.
Do not mount or open the .img file before verifying, because some systems alter it and the check will fail. The README text still shows 0.8.6 file names in places. Substitute 0.8.7, as the README itself says to do for other versions.
Step 4: Flash the microSD card
- Insert the microSD card into your computer.
- Open Balena Etcher or Raspberry Pi Imager, the two tools the SeedSigner README recommends. On Windows it suggests Raspberry Pi Imager first.
- Choose the verified
pi0image and the card, and write it. This erases the card. - Let the tool finish its verify step.
The image is for a card of 64 MB or larger. You do not need to format the card first.
Step 5: Fit the card and batteries
- Make sure no batteries are in the device.
- Push the microSD card into the spring-loaded port until it seats. Do not force it.
- Open the battery cover on the back.
- Fit three matching AAA batteries, following the + and - marks.
- Close the cover.
Alkaline or rechargeable NiMH AAAs both work. Use three of the same type and charge level. Power the device from the batteries or from USB-C, one at a time. Take the batteries out before you plug in USB-C.
Step 6: First boot
- Inserting the batteries starts the device. There is no switch.
- Wait. The SeedSigner project says the logo takes about 45 seconds to appear.
- Use the DPAD and buttons to move through the menu.
The Plus models have a larger 240x320 display. Our metal SeedSigner Plus guide covers the display type setting (st7789 320x240). If the picture looks cropped or offset, set the display type as in that guide.
Step 7: Day to day
Make or load your seed, then sign.
- New to hardware wallets? Follow Set Up Your First Hardware Wallet to pair a SeedSigner with Sparrow.
- Want to make your own entropy? Follow Generate a Seed with Dice on a SeedSigner.
- Back up your words on metal before you hold real funds.
- Send a small amount first and spend it back before you trust the setup with more.
Battery life tips
- The listing says about 8 hours from fresh batteries. Signing takes a small fraction of that.
- Start each important session with fresh or known-good cells.
- Fit a full set of matching cells together. Do not top up with one new cell.
- Do not leave batteries in between sessions. The device has no off switch, so it runs whenever cells are fitted.
- Keep a spare set of AAA batteries with the device, in a separate bag.
End a session
- Finish signing and note anything you need.
- Take the batteries out.
The SeedSigner project says seeds are stored in memory only while powered, and that memory is wiped when power is removed. Nothing is saved for later, so your written backup is your only copy. If you turned on persistent settings, those settings are kept on the card. The seed is not.
Store the batteries separately from the device.
Troubleshooting
Nothing happens when I fit the batteries
- Take the batteries out and check the + and - on each cell against the marks.
- Try a fresh, matching set.
- Check that the cells touch the contacts on both ends.
- Check that the microSD card is fully seated.
The screen stays black or shows no logo
Wait a full minute first. Then check the card. If the image was not written correctly, write it again and let the verify step finish. Try the other flashing tool if one fails, as the README suggests.
The device boots and then goes flat quickly
Swap in a fresh matching set. If it keeps happening with fresh alkaline or fully charged NiMH cells, contact us.
Picture cropped or offset
See the display type note in Step 6.
Still stuck
Contact us through the shop with your order number and a photo of the open battery compartment. Do not photograph a screen showing seed words.
What’s next
- Set Up Your First Hardware Wallet
- Generate a Seed with Dice on a SeedSigner
- How to Assemble a Metal SeedSigner Plus
- Self-Custody Basics
This is general information about holding your own bitcoin. It is not financial, tax or legal advice.
Sources checked 1 November 2026: shop listing and four photos for the SeedSigner Plus Battery Edition; SeedSigner release 0.8.7 and its README.
Frequently Asked Questions
Does the SeedSigner Plus Battery Edition have a power switch?
No. The shop listing says there is no power switch: insert the batteries to start it and take them out when your session is finished.
How long do the batteries last?
The shop listing says a set of fresh batteries gives about 8 hours of runtime. That is the maker's figure as listed.
Are batteries included?
No. The listing says batteries are not included. You supply 3 x AAA.
Can I use rechargeable AAA batteries?
Yes. Alkaline or rechargeable NiMH AAAs both work. A Pi Zero needs a steady 5 V and three AAAs never supply that directly, so the device steps the voltage up; NiMH cells sit inside the same range alkalines pass through as they run down. Use three of the same type and charge level.
Can I run it from USB-C with the batteries in?
Power it from the batteries or from USB-C, one at a time. Take the batteries out before you plug in USB-C.
Does it store my seed?
The SeedSigner project says its software holds seeds in memory only while powered and wipes that memory when power is removed. Taking the batteries out ends the session. Your written backup is the only copy.
Does it have WiFi or Bluetooth?
No. The listing says the Raspberry Pi Zero v1.3 board has no WiFi or Bluetooth communication capability, and the USB-C port is power-only.